Eagle Tool US ET18721 Installer Drill Bit Shank, Użat b'Kapijiet Interkambjabbli tal-Bit tal-Iswiċċ, 3/16-il pulzier minn 21-il pulzier, Magħmula fl-Istati Uniti 3/16 pulzieri 21 pulzieri.

Name: Eagle Tool US ET18721 Installer Drill Bit Shank, Użat b'Kapijiet Interkambjabbli tal-Bit tal-Iswiċċ, 3/16-il pulzier minn 21-il pulzier, Magħmula fl-Istati Uniti 3/16 pulzieri 21 pulzieri.
Brand: Eagle Tool US
SKU: 0850078004116
Availability: InStock

Brand:Eagle Tool US

3.9/5

€

Eagle Tool ta 'daqs individwali, xikel tal-azzar tar-rebbiegħa flessibbli. Ix-xkuk ta 'l-azzar tar-rebbiegħa flessibbli jiġu b'toqob ta' akkomodazzjoni tal-ħut, tliet imqabad ċatti, li ma jiżolqux u talja ta 'l-art li ma tiżloqx għar-ras interkambjabbli. Toqba tas-sajd tal-wajer fit-tarf taċ-ċokk. Ix-xejk ikejjel dijametru ta '3/16-il pulzier b'tul ta' 21 pulzier.

Ammont

Żid mal-CART Ixtri issa

EAN: 0850078004116

Kategoriji Għodda u Titjib tad-Dar, Għodda tal-Enerġija u tal-Idejn, Power Tool Partijiet u Aċċessorji, Power Drill Partijiet u Aċċessorji, Drill Bits, Installatur Drill Bits,

Set kamin sostitwibbli u allen wrench kit ETAKIT2. Toqba tas-sajd tal-wajer fit-tarf taċ-ċokk. Ċatt li ma jiżloqx (tarf tat-tħaffir) u maqbad tliet ċatti li ma jiżloqx (tarf taċ-ċokk). Xank tal-azzar tar-rebbiegħa flessibbli. Għall-użu mal-Kapijiet ETS375, ETS562, ETH375, ETM375, u Extension Adapter ETHXKIT187.

Brand	Eagle Tool US
Country of Origin	USA
Cutting Angle String	135 Degrees
Domestic Shipping	Item can be shipped within U.S.
Finish Type	Black Oxide
International Shipping	This item can be shipped to select countries outside of the U.S.
Item model number	ET18721
Manufacturer	Eagle Tool US
Material	Alloy Steel
Shank Type	Round

5 Star

4 Star

3 Star

2 Star

1 Star

Ikteb ir-reviżjoni tiegħek

L-email tiegħek mhux se tiġi ppubblikata. L-oqsma obbligatorji kollha huma mmarkati bi^*

Il-klassifikazzjoni tiegħek

Scritto da: Amazon Customer

Much better than single piece design

I have a business that provides low-voltage installation services. I greatly prefer an interchangeable setup like this over single piece (bit plus shaft design). With the single piece once you dull the bit you have to replace the entire thing (at $30-50 a pop), not to mention you end up needing 4-8 different bits to accommodate different drill bit sizes and lengths. It is easy to attach a new bit and the lip design helps prevent the bit from spinning loosely. The reason for 4 stars is because you have to really make sure to get the screws tight on this otherwise you end up with a bit stuck inside the wall. FYI the 90 degrees is for the entire length of the rod, dont expect to make a 1" hole and bend this at a sharp 90 degree angle. Also the larger the drill bit the slower you should go with your drill. If you try to push a 3/4" bit through a double 2x4 header at max speed you will likely break the rod before you drill through.

Scritto da: Jarrod Major

A decent size for those hard-to-reach places

Pretty simple tool, not much to say, it does the job. 1/4" shank is very rigid. Like the convenient hole on the drill side for wire pulls.