Rockwell RK9002 JawHorse Sheetmaster Workstation Portable

Brand:Rockwell

3.7/5

€

DESKRIZZJONI TAL-PRODOTT Il-heet-duty JawHorse Sheetmaster jismu hekk għaliex jista 'jappoġġja folja sħiħa ta' 8 x 4 plywood waħdu. M'hemmx bżonn li ċċempel lil ġar biex jgħinek iżżomm proġett meta jkollok il-JawHorse. Żomm idejk liberi biex tuża l-għodda tiegħek minflok tużahom biss biex issaħħaħ ix-xogħol tiegħek. U għolli l-proġett tiegħek mill-art u sa għoli tax-xogħol komdu. Il-Sheetmaster huwa verament 3-in-1 peress li għandu workbench, viċi, u funzjonalità tal-istampa tal-magni. Huwa b'saħħtu biżżejjed biex jimmaniġġja t-tgħawwiġ jew l-iddrittar tal-metall, magħmul minn azzar solidu b'10x il-forza tal-ikklampjar ta 'morsa standard, u tiftaħar bil-qawwa tal-ippressar industrijali ta' pressa ta 'magna ta' tunnellata. Huwa ta '53 lbs, li huwa sostanzjali, iżda jeħtieġ li jkun biex jappoġġja proġetti ta' 600 lbs b'1 tunnellata ta 'pressjoni ta' kklampjar. Iżda huwa ddisinjat b'għadd sħiħ ta 'karatteristiċi biex jagħmilha faċli biex tużah. Ir-riġel ta 'wara jirdoppja bħala manku, u s-saqajn ta' quddiem għandhom roti li jistgħu jinfetħu, sabiex tkun tista 'tgħolli d-dahar u timbottaha madwar is-sit tax-xogħol bħal karretta. Barra minn hekk, il-pedala tas-saqajn tagħmel ħafna mix-xogħol tal-ikklampjar għalik, u tħalli idejk tassew ħielsa. Huwa 39 "x 39" x 34" meta wieqfa u 29 "x 14" x 13 "meta mitwija. għaliex huma kunfidenti fil-prestazzjoni tal-għodod tagħhom. AMAZON.COM Il-Rockwell RK9002 JawHorse Sheetmaster huwa l-uniku post tax-xogħol li jkollok bżonn grazzi għal aktar minn tunnellata ta 'forza ta' kklampjar, kostruzzjoni ta 'l-azzar kollu solidu bħala blat, disinn li jintewa li jinġarr, u pedala tas-saqajn għal ikklampjar u xogħol mingħajr idejn. Għal spedjenza addizzjonali, l-iswiċċ li jillokkja l-illokkjar jippermettilek li tissakkar materjal—bħal folja sħiħa ta’ plywood—f’postha u tirrilaxxha faċilment b’ċaqliq ta’ swiċċ, li jagħmel il-JawHorse Sheetmaster żieda konvenjenti u affidabbli għall-workshop jew ix-xogħol. sit.RK9002 JawHorseSheetmaster F'daqqa t'għajn: * Żomm sa folji ta' 48 pulzier f'għodda waħda b'forza ta' kklampjar mingħajr idejn * Titwi malajr għal 43 libbra li jistgħu jinġarru b'roti b'linja dritta integrati għal portabbiltà aktar faċli * Dimensjonijiet: 39 pulzier b'39 pulzier b'34 pulzier bil-wieqfa; 29 pulzier b'14-il pulzier b'13-il pulzier mitwija * Appoġġjat minn garanzija limitata ta 'ħames sninIl-Rockwell JawHorse Sheetmaster jista' jiffunzjona bħala bank tax-xogħol, morsa, u pressa tal-magni (ara ikbar). dan. Ix-xedaq qawwija tal-ikklampjar tal-JawHorse Sheetmaster jippermettulek tikklampja b'mod sikur prattikament kull ħaġa, sabiex ikollok aċċess mingħajr idejn biex tlesti l-proġett tiegħek b'mod sikur. Tista 'anki tikklampja oġġetti wesgħin bħal bibien jew folji sħaħ ta' plywood grazzi għall-wisa 'tal-ikklampjar ta' 49 pulzier. Sempliċement issettjaha, illokkjaha, u clampha.Workbench VersatiliGrazzi għad-disinn flessibbli tiegħu, il-JawHorse iħallik ttella' l-proġetti tiegħek u 'l barra mill-art f'għoli ta' xogħol komdu. Sempliċement ikklampja biċċa plywood ordinarja fil-JawHorse u għandek bank tax-xogħol perfett. Tista 'anki tużaha fuq il-post tax-xogħol bħala pjattaforma b'saħħitha għal srieraq tal-mitra, srieraq tal-madum, u aktar. Barra minn hekk, il-bażi tat-tripod tagħti stabbiltà eċċezzjonali fit-terren kollu—u r-riġlejn ta’ quddiem jinkorporaw toqob biex jippermettu rbit għal impjiegi aktar permanenti.Press tal-Vice u tal-Magni Kemm jekk qed tgħawweġ il-metall jew tiddrittah, is-saħħa u l-istabbiltà tal-JawHorse Sheetmaster jippermettulek tkun aggressiv max-xogħol tiegħek. Il-JawHorse Sheetmaster huwa magħmul minn azzar solidu u għandu 10 darbiet il-qawwa tal-ikklampjar ta 'morsa regolari. Fiha wkoll il-qawwa tal-ippressar industrijali ta 'pressa ta' magna ta 'tunnellata waħda. X'hemm fil-BoxOne Rockwell RK9002 JawHorse Sheetmaster.Il-JawHorse Sheetmaster huwa faċilment jintrewa—u 43 libbra, huwa faċli li tittrasporta lejn is-sit tax-xogħol (ikklikkja kull wieħed biex tkabbar) . MILL-MANIFATTUR Issa tista 'tappoġġja u tikklampja folja sħiħa ta' plywood 8x4 b'għodda waħda biss. Il-Rockwell RK9002 JawHorse Sheetmaster huwa l-helper aħħari fuq il-post tax-xogħol. It-tħaddim mingħajr idejn tiegħu jagħmilha faċli biex tikklampja u żżomm il-biċċiet tax-xogħol tiegħek. Ħalli l-sheetmaster jagħmel l-azjenda u l-istabbilizzazzjoni kollha għalik li tippermetti li tuża idejk b'xejn għall-għodda tiegħek minflok tuża idejk biex tistabbilizza x-xogħol tiegħek. L-imqabad li ma jtaffix fuq ix-xedaq jgħin biex jipproteġi x-xogħol tiegħek. Il-Sheetmaster huwa heavy duty u jappoġġja sa 600 lbs. ta 'piż b'sa 1 tunnellata ta' forza tal-ikklampjar. Meta tkun lest, itwiha għal ħażna kompatta jew għal trasport faċli. Il-Rockwell Sheetmaster għandu roti tal-iskuters biex jirromblaw faċilment lejn u mill-post tax-xogħol. Ir-riġel ta' wara tirdoppja bħala manku biex it-trasport ikun saħansitra aktar faċli. Bl-Rockwell JawHorse sheetmaster, issettjaha, illokkjaha, u qabbad it-triq tiegħek għal appoġġ idejn ħielsa għall-proġetti tiegħek. Ara iktar

Ammont

Żid mal-CART Ixtri issa

EAN: 787721480389

Kategoriji Għodda u Titjib tad-Dar, Għodda tal-Enerġija u tal-Idejn, Power Tool Partijiet u Aċċessorji, Stands u Bażijiet mobbli, Stands,

[FAĊLI BIEX TIĊQAQQA] Faċli biex taħżen. B'lukketti tar-riġel li jerħu malajr il-JawHorse jintewa malajr 'l isfel u r-roti li jinfetħu jagħmluha faċli biex timbotta. [TRIPOD BASE] Tliet saqajn pożizzjonati perfettament fil-fatt jipprovdu aktar appoġġ fuq art mhux uniformi milli kieku erba' saqajn. [NO MAR PADS] Magħmula mill-uretan sabiex jaqbdu l-materjal mingħajr ma jħallu marki, perfetti għal proġetti ta 'xogħol ta' l-injam premium. [1 TUNNELLATA TA 'FORZA TA' KCLAMPING] 2000 lbs ta 'pressjoni tfisser li l-proġett mhu sejjer imkien, u b'tagħbija massima ta' 600 lbs jista 'jimmaniġġja ħafna. [ŻOMMA KOLJA SĦIĦA TA' PLYWOOD] B'sa 49" ta 'firxa ta' kklampjar u metodu ta 'kklampjar ta' 3/8" għal kull pass. [KOSTRUZZJONI TA' L-AZZAR KOLLHA] Mibnija biex idum u mibnija biex iżżomm l-aktar proġetti importanti tiegħek waqt li idejk tibqa' ħielsa biex tuża l-għodda tiegħek.

Batteries Included?	‎No
Batteries Required?	‎No
Color	‎Black
Customer Reviews	4.7 4.7 out of 5 stars 780 ratings 4.7 out of 5 stars
Is Discontinued By Manufacturer	‎No
Item model number	‎RK9002
Item Package Quantity	‎1
Item Weight	‎27 pounds
Manufacturer	‎Rockwell
Part Number	‎RK9002
Product Dimensions	‎17.9 x 39.8 x 15.9 inches
Warranty Description	‎Limited 2-year

5 Star

4 Star

3 Star

2 Star

1 Star

Ikteb ir-reviżjoni tiegħek

L-email tiegħek mhux se tiġi ppubblikata. L-oqsma obbligatorji kollha huma mmarkati bi^*

Il-klassifikazzjoni tiegħek

Scritto da: WatchItBurn

Not cheap

Not cheap but it's certainly not cheap. Yeah, It costs what I make in a day but damn it's built like it costs what I make in a day to make. Solid tool, holds small engine blocks, painting projects, welding projects, glue ups and I'm pretty sure with the right accessory, it'll hold up a rocky marriage, or hold back a zombie horde. We've all heard of generational wealth, I don't have any of that but I'll tell you what, This here is a generational tool. Ur kids'll be using this to hold what's left of the American dream together long after you're gone. Hell, if theres anything that can hold whats left of ol US of A together, it'd be this tool right here. Thank you Rockwell. Other brand simply can't hold a torch to you.

Scritto da: Andrew Czop

Great tool!

I have never owned a jawhorse before, and decided to get this newer model, the sheetmaster, instead of the original. It was a little more money, but the added features and ability to handle 48" wide sheets without buying additional adapters was a bonus. It is my understanding that this version is a little beefed up from the original, has the 48" capacity out of the box, has a different wheel/rolling system, and is easier to break down. I wanted a jawhorse to basically use as a portable vise. To hold material securely when cutting off 2x material, to hold larger items while sanding, chiseling, or ripping, etc. I was sick of working on the ground, or inconveniently on saw horses, etc. Since I got it, I've also used it as a miter saw stand, which worked great. I watched and read a lot of reviews, and determined that even though this unit is expensive, it would be worth it to me, and it definitely is. It is super easy to set up and break down. It takes maybe 30 seconds to unfold a few legs and flip it over, and vice versa. The clamping force is great. I haven't tried to measure it, but it is definitely more than enough to secure whatever you put into it. The jawhorse is not really prone to tipping due to it's design, but obviously can if you force it, and I say this to say that from my off the cuff tests, I get the unit to tip before I can dislodge/slip the material that is locked in the jaws. This is to say, the clamping force is fantastic. And super easy to clamp something by allowing you to use your foot, which frees up both hands to make sure the piece is placed just the way you want it. I have yet to put a full sheet of anything into the jaws. It comes with an extra jig piece that quickly clamps and holds holds two pieces of 2x material at 90 degrees that is meant to be additional support for full sheets. The two pieces at 90 degrees form an "L" where the mid point of the long side of the "L" rests on the jawhorse to support the long dimension of the sheet, and the short side of the "L" rests on the ground. It looks to be pretty quick to set up, but you'd have to have that 2x material handy whenever you plan to do full sheets (maybe not as travel friendly then), and would have to set up the clamps each time. And then you wouldn't want to lose the clamp jig, and it does not store with the unit itself. This is all to say that yes it does full sheets, and I'm sure it is great at it, but it's not a fully integrated solution that all packs away into the unit itself. If you're going to be cutting a number of sheets, it's definitely worth it to set up the extra jig and go to town, but otherwise, you'll probably not be using it for single sheet cuts. This doesn't mean that the 48" jaw capacity is not useful though, beacause there are still times where you may want to hold something "long ways" by its <48" dimension, and as long as it's not wider than a few feet, you wouldn't need the support braces. One gripe I have about the unit, the only one so far (unless you count how cumbersome I view the support brace setup to be), is that when you try to wheel it, (a neat feature by the way, that you can compact it, and it wheels with the leg as a handle), a combination of the wheels being small and close together results in a lot of rocking while wheeling. You wind up fighting it while wheeling it, even on flat ground to an extent. Like a crappy suitcase where it's constantly on one wheel, then the other, then the other, back and forth, etc. You have to baby it to get it to roll properly, even on flat ground. If you are trying to do stairs, or go over grass or anything else, forget it. I personally have about given up on the wheels and just carry it. If you're going 10 or 20 feet across the garage, the wheels are OK, but more than that, it saves time and frustration to just carry it. My understanding is that the two wheel design this unit has is different than the single roller the original jawhorse has, and is supposed to be better. I haven't used the original, so I don't know how that one works, but I can say that I am not too impressed by the wheeling capability of this unit. It's fine for flat ground, and I guess not *too* bad overall. Let me say this... it's better than not having them, so there's that. But I do think they could be improved. One other note is that you need to be careful with the clamping force. It's hard to control just how much you use, and when removing it, just like an E-brake on a car, you need to apply *just* a little more force than you used to clamp/lock it, which means a little more clamping force needs to be applied to remove a clamped item. You wouldn't want to use it to hold anything delicate. For example, I tried a test piece of 1/2" copper pipe, and found that it was difficult to secure the pipe without crushing it out of round. Even when I got it to hold without hurting it too much, it was far too easy to press too hard on the foot pedal when releasing it and just smash the copper flat. You don't realize how much clamping force it really has until you see this and how easy it is to do. It's one thing to clamp things in a normal bench vise where it closes slowly, turn by turn by hand, but with the jawhorse where you use your foot and a lot of clamping force is applied very quickly for what feels like not pressing very hard with your foot, it can be a problem for these delicate items. This is awesome when grabbing wood and items that aren't easily crushed, but it does mean that you want to be careful with anything that you would be weary about in a normal vise. I would remove a star because of the wheels, but it's not a key enough feature to me to do that. It really is a 5 star item IMO. Extremely well made, performs its functions extremely well, and is just a down right awesome tool. I love it.

Scritto da: PhotoKing

A very useful tool

I had trouble deciding if this was a 5 or a 4 star product. Pro's: Very sturdy, holds a full sheet of plywood, fairly portable Con's: Clumsy to roll and carry, tripping hazard, comes with silly looking wood holder, very hard to remove yellow part, see below for rest. Overall I like the tool, it's my new favorite thing. Long gone are the days of having to clamp a piece of wood to my bench to cut with a recip or scroll saw. To cut odd shaped things I would have to drag my tools outside. Now inside I can set it up, open, clamp and work. Clamp a piece of wood in the jaws and place a small table saw, or make it into a bench. The jaws have removable rubber covers. However all that said the things I don't like are a few. For one, after you unfold it, it's hard to pick up and really awkward. While 50 pounds isn't super heavy, it isn't light. And I hurt my back a few times. When folded you have to make sure you fold it in the right order, folding the legs down first so it folds tighter. It can fold other ways that are less tight. This things is awkward to carry. It doesn't roll well, it's very tipsy. Rolling it up stairs is a good way to dislocated a shoulder. Carrying it is even harder, I wish there was an easy way to carry this upright. If you clamp a pipe, you will flatten the pipe. There is no pipe holder, there are some V ridges, but it would be nice to have. The yellow sled is designed to come out and reverse. But it's so well engineered that the paint makes it very tight to remove, it's a tug of war to that thing out each time. I found oiling the bearings holding it in helps. Greasing the rails made a mess. There is no fine clamping force, the clamp is designed to sort of walk the yellow sled forward and it moves it in 1/2" increments. So if you want to compress something like a spring, or maybe even crush a can - you may have a hard time if it's pushing back. I found that the foot pedal a little too high, and you have to remember to lock and unlock the thing each time you want to clamp or unclamp. Unfolded it's very stable, but for whatever reason I seem to trip over one of the legs every single time I pass by. I don't think that's a design flaw, yet something about that design I keep tripping over it. It comes with a little device that you attach to a piece of wood and it creates a sort of foot to hold up large boards. But as nice as it is, there is no place to put it. It can't fit on the horse, and it's so easy to lose.

Scritto da: Manuel M.

Einfach nur genial!

Servus zusammen, ich weiß überhaupt nicht warum dieses Gerät oder besser die Art, hier in Mitteleuropa fast gänzlich unbekannt ist. Ich bin durch einen Megazufall darauf gestoßen. In einem Beitrag von April Wilkerson dachte ich mir, WTF, was ist das da? In der Liste Ihrer Werkzeuge stand dann JawHorse. Was zum Teufel ist ein JawHorse!?! Ich kann sagen, ein einfaches und wirklich geniales Teil. Ich habe darauf geachtet dass ich Werkstücke von mehr als 1200mm einspannen konnte, ja und Zack, da habe ich mir das Dingens hier bestellt. Egal was, drauflegen, einspannen (der Druck ist hervorragend einstellbar- ich spanne u.a. 10mm Gipsfaserplatten ein) und loslegen. Der Stand des Bocks inkl. des Materials ist einfach Mega! Fazit: Jeder der Plattenwerkstoffe oder Türen bzw. Fenster aufarbeitet bzw. bearbeitet sollte sich sowas hier anschaffen! Wenn möglich noch mehr Sterne! Vielen Dank an April! Beste Grüße

Scritto da: HOOCH 463

Rockwell Jaw Horse

Arrived very promptly impressed with the delivery service. As mentioned in other reviews it is a little on the heavy side, but this is due to the outstanding construction. It truly is built to last. Typical man I didnt bother with the instructions to put it up and took a while to figure it out. It requires turning on its back and getting the legs and clamp system opened in the correct order. If you have a back injury or mobility issues this is not something you will want to be putting up and down on a regular basis. But the footprint isnt too large so could be left up for the home DIY ehthusiast with enough space. Folding it up requires it to be flipped over again and I have noticed that when you do start to turn it over, and put pressure on any of the legs to act as the pivot, they are prone to start to fold up. It is essential that all safety clips are checked to be firmly seated before you start to roll it over. Due to its weight and shape it will soon trap your hand or collapse in a heap if you dont follow the instructions carefully. But it does exactly what it says on the box. 10/10 for design and construction very impressed indeed.

Scritto da: Frank

it folds and stores easily but is extremely sturdy and strong when in use ...

I purchased this product with the expectations of it being a mid quality tool. It is anything but. I am very impressed with the quality of workmanship and design. I wanted the capability to handle full sheets of plywood but did not want a bench that would forever be in the way when not in use. it folds and stores easily but is extremely sturdy and strong when in use (not something I'd expect from something with folding legs). Lastly the foot controls are genious as it frees up both hands for larger objects.

Scritto da: John Aflack

Solo Mate

The Rockwell RK9002 48-Inch JawHorse Sheetmaster is the ideal partner for the solo handyman. It extends to hold a 4x8 ft. plywood sheet, and comes with a clamp to extend the support surface using 2 by 4's. It is robust and is not made out of cheap stamped metal. The 3-legged system prevents tipping. In addition it can be easily folded up and comes equipped with built-in wheels. It is worth the investment. There are accessories available for clamping chainsaws, mitre saws and rollers. You won't be disappointed with this as your work project partner!

Scritto da: Dallas from E-Town

Really solid grip.

Big enough to hold larger work pieces without tipping over. Grips well.