Kerick Valve MA052 PVC Mini Float Valve, Tank Mount, Arm Aġġustabbli, 1.5 gpm f'60 psi, 1/2 NPT Male

Name: Kerick Valve MA052 PVC Mini Float Valve, Tank Mount, Arm Aġġustabbli, 1.5 gpm f'60 psi, 1/2 NPT Male
Brand: Kerick Valve
SKU: 0789164274709
Availability: InStock

Brand:Kerick Valve

3.4/5

€

Dan il-valv float Kerick MA052 huwa stil ta 'muntaġġ ta' tank b'driegħ aġġustabbli, u huwa magħmul minn PVC b'ħardwer ta 'l-istainless steel 18-8. Il-valv għandu orifiċju ta '0.093 u r-rata ta' fluss stmata tiegħu hija ta '1.3 gallun kull minuta (gpm) f'40 libbra kull pulzier kwadru (psi) u 1.5 gpm f'60 psi. Id-daħla tal-valv għandha ħjut estiżi maskili 1/2 NPT b'washer tas-siġillar u ġewż tal-ġamm għall-immuntar minn ħajt tat-tank, u l-iżbokk tal-valv huwa ħieles. Il-valv huwa magħmul minn PVC (polyvinyl chloride) approvat mill-Fondazzjoni Nazzjonali tas-Sanità (NSF), is-siġilli sostitwibbli tiegħu huma magħmula minn TPE (elastomer termoplastiku) għal durabilità u reżistenza kimika, u l-ħardwer tiegħu huwa magħmul minn 18-8 stainless steel għal reżistenza għall-korrużjoni. Il-valv għandu dijametru ta '1.5 u 4 float twil tal-polyethylene imwaħħal mad-driegħ tal-lieva tal-għeluq aġġustabbli. Dan il-valv tal-float huwa adattat għall-użu f'varjetà ta 'applikazzjonijiet, bħal funtani u tankijiet tal-ilma tal-bhejjem. Il-valvoli tal-float jużaw virga u ballun float mwaħħla ma' lieva ta 'għeluq tal-valv biex jikkontrollaw il-fluss ġewwa jew barra minn tank. Il-ballun float jogħla jew jaqa 'mal-livell ta' likwidu fit-tank, jibdel l-angolu tal-lieva ta 'għeluq tal-valv. Meta l-angolu tal-lieva tal-valv jinbidel biżżejjed, il-valv jinfetaħ jew jagħlaq. Il-valvi tal-float huma kklassifikati skont il-volum ta 'likwidu li jista' jgħaddi minnhom bi pressjoni partikolari biex jiġi żgurat li t-tank jista 'jimtela mill-ġdid malajr kemm jista' jitbattal. Il-materjal li minnu huwa mibni float valve għandu jkun adattat għal-likwidu li jopera fih, li jista' jkun korrużiv jew f'temperatura estrema. Il-valvoli tal-float jintużaw biex jirregolaw awtomatikament il-livell ta 'likwidu fi ħdan it-tankijiet f'varjetà ta' applikazzjonijiet, bħal funtani, tankijiet tal-ilma tal-bhejjem, torrijiet tat-tkessiħ, u impjanti tal-manifattura kimika.Kerick Valve timmanifattura valvi ta 'kontroll tal-livell tal-fluwidu għal applikazzjonijiet industrijali. Il-kumpanija, imwaqqfa fl-1994, għandha kwartjieri ġenerali f'Jacksonville, FL.X'INHU FIL-KAXXA? * Valv MA052 * PF154 float ball

Ammont

Żid mal-CART Ixtri issa

EAN: 0789164274709

Kategoriji Industrijali u Xjentifiċi, Idrawlika, Pnewmatika u Plumbing, Fittings, Valvoli, Float Valves,

Daħla bil-kamin maskili 1/2 NPT u ħruġ ta 'fluss ħieles. Nota: MA052 għandu ħajt tal-pajp 1/2 NPT. Dan huwa estremament komuni fid-dinja tal-plaming. Il-ħajta tkejjel madwar 3/4 ta 'pulzier fid-dijametru, dan huwa żball komuni għal dawk li mhumiex familjari mal-ħjut tal-pajpijiet u l-plaming. Tank mount b'ħjut estiżi fuq in-naħa tad-daħla tal-valv għall-immuntar permezz tal-ħajt tat-tank. PVC għal reżistenza għall-korrużjoni. Rata stmata ta 'fluss sa 1.5 gpm f'60 psi.

Brand	Kerick Valve
Country of Origin	USA
Domestic Shipping	Item can be shipped within U.S.
Exterior Finish	Stainless Steel
Inlet Connection Size	.5 Inches
Inlet Connection Type	National Pipe Tapered
International Shipping	This item can be shipped to select countries outside of the U.S.
Is Discontinued By Manufacturer	No
Item Dimensions LxWxH	7.5 x 2 x 3.3 inches
Item model number	MA052
Manufacturer	Kerick Valve
Material	PVC
Outlet Connection Type	MNPT
Product Dimensions	7.5 x 2 x 3.3 inches; 1.6 Ounces
Specification Met	NSF

5 Star

4 Star

3 Star

2 Star

1 Star

Ikteb ir-reviżjoni tiegħek

L-email tiegħek mhux se tiġi ppubblikata. L-oqsma obbligatorji kollha huma mmarkati bi^*

Il-klassifikazzjoni tiegħek

Scritto da: Ryan Kamba

Works - but for how long

This is the second one I bought. They last for about 6 months. Then they get stuck in the closed position. Going a different route next time.

Scritto da: Thomas C.

Size misleading

Too small

Scritto da: J.B. Cabell

Excellent value

This thing is much smaller than I had pictured in my mind. The whole assembly is barely longer than my open hand, so it can fit into tight spaces for a fountain project, or in a sump to maintain water level in a swimming pool. The description here at Amazon.com is nonsense, giving its length as 1 inch: The actual overall length is about 7.5 inches, or 6.5 inches from the mounting flange to the tip of the float, worst case. (See the second vendor-supplied image with the valve photographed against an inch grid for a better understanding of its actual size.) With allowance for installation and adjustment, the valve could be squeezed into a space as small as 8 inches by 2 inches. If installed in a bulkhead, the mounting surface should be flat and no thicker than about 0.25 inch, to allow enough thread protrusion on the outside to attach a threaded pipe fitting. Bulkhead mounting is optional: The male pipe thread on the valve is slightly tapered and can be screwed into any female pipe thread fitting, using Teflon tape on the threads for a watertight seal I gauged the valve orifice with a drill rod at 0.094 inch (3/32 inch) diameter, which accounts for the low flow rate specification. You may not want to fill a swimming pool with it from scratch, but for a typical backyard pool it will allow more than enough water to flow to compensate for evaporation loss. The float arm pivots on a stainless steel cotter pin, so it could easily be disassembled, should the need arise, although at the low cost of the assembly it may be more economical to replace it entirely. Depending on the placement of the valve, the float can be adjusted over a liquid level range of at least 4 inches, possibly as much as 6 inches, by loosening the stainless steel wing nut. One of these valves was successfully used to maintain the water level in a neighbor's swimming pool last summer during a month-long absence. See the customer photo that I posted, showing the minimalist installation with a few pieces of PVC plastic plumbing, an ordinary brick and a garden hose. The only problem I encountered was the hose of the automatic pool sweep once getting hung up on the valve, keeping it open continuously. Because of the restricted flow, no flooding occurred by the time I discovered the problem the next day. If I use it next summer again, I'll mount the valve with some sort of bumper or "fence" around it to keep the pool sweep hose clear, and I'll replace the leaky plastic hose fitting with a sturdier brass fitting.

Scritto da: William D Jamison

Works as Intended

This was easy to install and I use it in a backyard water feature. It has a 1/2" intake and seals well when full.

Scritto da: dreamer

Good valve when working, but 4 of them have failed after about 6 months.

The valves last welll for months, but then the seal, a 1/4" white plastic, nail-shaped part, is prone to internal bubbles full of water, which make the valves suddenly begin to leak badly, wasting water. The seals are difficult to replace down in our swimming pool filler sump, so I replace the whole valve. ...but proper molding by the manufacturer would have been much better. They the seals appear to have been molded with air bubbles, which eventually fill with water under pressure, so the seal grows a flexible lump. ...which you can break with a pin, and water comes out. I would replace with different brand, but all these small valves seem to have the same form. ...appear to be made, maybe, by the same maker.

Scritto da: Consumer Folk

Worked Perfectly in Fountain Setup. Excellent Sizing Guidance on Product Page

Bought as a replacement valve. As a non-plumber, I greatly appreciated the product description and picture showing the actual size for the item (the thread is about 3/4", but matches the 1/2" NPT standard). Once installed, this new valve immediately stopped the leak that I had with the original valve.

Scritto da: Salvador

Reliable and cheap.

My supply pipe coming out of the pool, flush on the wall tiles is 1/2". So I buy a 1/2" barb fitting male NPT, 70 cents lowe's. Soften the barb fitting on a trial scrap 1/2" pipe to reduce the barb diameter, or you can sand the barb with drill chuck to the id of barb fitting, around .010 bigger over the 1/2" pipe ID. (Do Not Drill the pool pipe ID to make it bigger, you need a smooth weld when you apply a primer and glue on pipe for water pressure application integrity, wait about 2 hrs. Connect a 1/2" elbow then the kerick valve, so the whole unit is parallel to the wall of the pool for less obstruction. I have it installed for about a 2 weeks now, set about halfway or middle of the mouth of the skimmer, with stable height the whole two weeks. Usually my pool go down 1/2" every 2 days, then I fill it up, about 30-45 minutes with timer, until the middle of mouth of skimmer. The water ball valve on the faucet is set on the low opening to avoid overfill just in case this kerrick valve malfunction. The thread on this is not a standard 1/2" NPT, but that 2 turn is enough, with the help of a provided nut, no leak, so no problem for me.

Scritto da: Tony Thiel

Does what I wanted it to do.

I wanted a water holding tank and used a 20 gallon Husky Garbage can, mounted this on it and it works just fine. I use the water with a very weak solution of fertilizer to water my 80 plus orchids and other plants. I had to use a couple of sturdy plastic plates to solidify the installation because the weight of the hose would buckle the area where it's mounted. But once that was done, it works just fine. October 28th, 2015 addendum: I think that something like this would also work great for adding water to an aquarium or fish tank. If the water coming out of your tap is chlorinated, letting it sit for a while will help dissipate the chlorine. This could also work as an emergency self filling water tank. Here in Hawaii, we are constantly warned about the possibility of a hurricane. A 33 gallon CLEAN garbage can filled with water would certainly help in an emergency. Just leave the cover on to keep dust and debris from getting into it. Actually, if you think hard enough, there are a lot of possibilities with this.

Scritto da: dave

Awesome

Awesome