Daħħal bil-kamin E-Z LOK għall-Inserzjonijiet tal-Kamin tar-ram Vane Uniku tal-plastik għax-xejn 1/4-20-(Pakkett ta '10,500 Count Total) 2000

Name: Daħħal bil-kamin E-Z LOK għall-Inserzjonijiet tal-Kamin tar-ram Vane Uniku tal-plastik għax-xejn 1/4-20-(Pakkett ta '10,500 Count Total) 2000
Brand: E-Z LOK
SKU: 0847554043585
Availability: InStock

Brand:E-Z LOK

3.9/5

€

E-Z Sonic Threaded Inserts għal PlasticE-Z Sonic inserts bil-kamin ultrasoniku għall-plastik huma dejjiema biżżejjed għall-ambjenti l-aktar ħorox u versatili biżżejjed biex jissodisfaw il-ħtiġijiet ta 'kwalunkwe applikazzjoni b'torque superjuri u reżistenza għall-ġibda. L-inserzjonijiet tal-ħajt tar-ram huma ddisinjati biex jitqiegħdu ħjut tal-magni standard f'partijiet stampati 3D u termoplastiku. Installa dawn l-inserzjonijiet tal-ħajt tal-metall ultrasoniku jew b'sewwieq tas-sħana. Id-disinn għax-xejn jissimplifika l-installazzjoni. Disponibbli f'inserzjonijiet ta 'ħajt għax-xejn f'qasir wieħed u doppju, inserzjonijiet ta' ħajt dritti f'konfigurazzjoni ta' flush jew flanġ. Karatteristiċi * Disinji għax-xejn u dritti * Installa ultrasonikament jew b'sewwieq tas-sħana * Disinn għax-xejn f'ventila waħda u doppja

Ammont

Żid mal-CART Ixtri issa

EAN: 0847554043585

Kategoriji Industrijali u Xjentifiċi, Imsiemer, Viti u Qafliet, Ġewż, Inserzjonijiet tal-Ġewż,

Ħjut b'saħħithom MAGĦMULA FAĊLI - Inserzjonijiet bil-kamin tar-ram ta 'kwalità għolja huma disponibbli kemm bil-pulzier kif ukoll bil-ħjut metriċi. STILI DISPONIBBLI - L-inserzjonijiet tapered E-Z Sonic huma disponibbli f'konfigurazzjonijiet ta 'vane wieħed jew doppju biex jissodisfaw ir-rekwiżiti tal-ħxuna tal-materjal tiegħek. GĦAL UŻU BL-APPLIKAZZJONIJIET - L-inserzjonijiet bil-kamin għall-plastik huma ddisinjati biex jitqiegħdu ħjut tal-magni standard f'partijiet stampati 3D u termoplastiku. INSTALLAZZJONI FAĊLI - Installa dawn l-inserzjonijiet bil-kamin tal-metall ultrasoniku jew b'sewwieq tas-sħana. Id-disinn għax-xejn jissimplifika l-installazzjoni. INSERTI BIL-KAMIN GĦALL-PLASTIK - L-inserzjonijiet tal-ħajt ultrasoniku E-Z Sonic għall-plastik huma ddisinjati għal installazzjoni ta 'wara l-iffurmar f'materjali termoplastiku.

Brand	E-Z LOK
Color	Plain
Country of Origin	Taiwan
Item Dimensions LxWxH	7 x 3 x 2.5 inches
Item model number	TH-420-SV
Manufacturer	E-Z LOK
Material	Brass
Product Dimensions	7 x 3 x 2.5 inches; 2.6 Pounds
Size	One Size

5 Star

4 Star

3 Star

2 Star

1 Star

Ikteb ir-reviżjoni tiegħek

L-email tiegħek mhux se tiġi ppubblikata. L-oqsma obbligatorji kollha huma mmarkati bi^*

Il-klassifikazzjoni tiegħek

Scritto da: Kindle Customer

Great insert, holds well in wood if you do it right. The insert I used was 1/4-20 15/16 long

I did a test where I drilled the recommend hole and pressed in one insert into some maple and I moved over 3 inches and put some 5 minute epoxy in between and a light film on the knurl. I pressed this in and let it cure for 3 days. I inserted a 1/4-20 hex head bolt in 2" long and tightened the bolt down slowly. The insert held fairly well at first but eventually pulled right out. I moved over the in insert with the epoxy on it and I turned the bolt down and it started to get fairly stiff to turn. I kept turning and then I heard a pop and the thought that the insert came lose. No, it was the back side of the 1" maple creaking out as I screwed it down. The flat ended bolt split the maple about 3 inches before I saw any of the bolt. The insert is still in the board as strong as the day I put it in the male hole. There great insert and I feel that under the right circumstances and installation Technic will work very well in wood and not just plastic. Ten wahoo's the the folks who designed this insert. Great job!

Scritto da: Bob Tobias

Works great on 3D prints and you may not even need a special tool!

The outside diameter of the top of these inserts, the end you press against, is 9.6mm. That's a tad wider than my soldering iron with its tip removed. I can set them perfectly without using any special-purpose soldering iron tips. I still use the 6mm tip from myShineNow Heat-set Insert Tips because I have them anyway. And, as long as we're talking dimensions, the inserts are 7.6mm long. You will, of course, want to make sure you are putting them into something at least that thick. Also, the diameter of the bottom end, the end that goes into the plastic first, is 9mm, should that be useful to your design.

Scritto da: DarkMavrik

works well

I just use a regular soldering iron to push these into place, works great go through about 100 a month with all the stuff I do and haven't had one fail yet

Scritto da: KMan

Great For 3D Printed Camera Accessories

I've 3D printed a few camera accessories such as tripod adapters and used these. They're the perfect length for standard tripod screws.

Scritto da: Lisa H.

Good quality

Use a lot for various 3D printing projects

Scritto da: Aerial-Pixel

These Excellent for 3D Prints

The media could not be loaded. These are perfect for installing 1/4-20 threads in 3D prints, love them. To install I just use a soldering iron @ 380C and press them in place. I've purchased them several times with no issues.

Scritto da: Nick

Works great for my 3d prints

I have used most of the pack at this point and am very happy with the quality.

Scritto da: ElllisGL

They work as expected.

I used this for a 3D printed camera quick release and it still in place.