Sensor Swiċċ MSX12 M4 360 Grad Multiple Fixture Mount Occupancy Sensor, abjad

Name: Sensor Swiċċ MSX12 M4 360 Grad Multiple Fixture Mount Occupancy Sensor, abjad
Brand: Sensor Switch
SKU: 0753573998341
Availability: InStock

Brand:Sensor Switch

3.1/5

€

Trid tagħti lill-kamra tiegħek dehra ġdida fjamanta u bi prezz baxx? Ħaresx aktar mill-assortiment tagħna ta 'Madum Nexus. B'aktar minn 20 stil minn fejn tagħżel, żgur li ssib l-istil li l-aħjar jaqbel mal-ħtieġa tiegħek. Ebda kolla messy jew adeżivi meħtieġa. Sempliċement qaxxar u waħħal il-madum Nexus ma 'wiċċ ċatt u niexef u uri l-kamra sabiħa ġdida tiegħek lill-ħbieb u l-ġirien tiegħek kollha. California teħtieġ l-avviż li ġej: TWISSIJA: Dan il-prodott fih kimiċi magħrufa mill-Istat ta 'Kalifornja li jikkawżaw kanċer jew difetti oħra tat-twelid jew ħsara riproduttiva oħra.

Ammont

Żid mal-CART Ixtri issa

EAN: 0753573998341

Kategoriji Għodda u Titjib tad-Dar, Elettriku, Swiċċijiet u Dimmers, Swiċċijiet tal-ħajt, Swiċċijiet Attivati bil-Moviment,

Dewmien ta 'ħin aġġustabbli, issettjat minn qabel għal 15-il minuta. Jaħdem b'dwal tal-bajja mmexxija jew fluworexxenti, dwal tal-istrixxi u apparat tad-dawl wraparound. It-teknoloġija infrared passiva ta '360 grad tipprovdi sa 60 pied ta' skoperta ta 'moviment fil-livell tal-art. Djar akriliku abjad taqbel ma 'tagħmir tad-dawl abjad. Jipprovdi mixgħul u mitfi awtomatiku għal tagħmir wieħed jew multipli għall-iffrankar tal-enerġija u l-konvenjenza.

Batteries Included?	‎No
Batteries Required?	‎No
Color	‎White
Country of Origin	‎China
Customer Reviews	4.1 4.1 out of 5 stars 44 ratings 4.1 out of 5 stars
Domestic Shipping	Item can be shipped within U.S.
International Shipping	This item can be shipped to select countries outside of the U.S. Learn More
Is Discontinued By Manufacturer	‎No
Item model number	‎MSX12 M4
Item Package Quantity	‎1
Item Weight	‎5.6 ounces
Manufacturer	‎Sensor Switch
Part Number	‎MSX12 M4
Power Source	‎AC
Product Dimensions	‎4.13 x 4.13 x 2.5 inches
Warranty Description	‎5 years

5 Star

4 Star

3 Star

2 Star

1 Star

Ikteb ir-reviżjoni tiegħek

L-email tiegħek mhux se tiġi ppubblikata. L-oqsma obbligatorji kollha huma mmarkati bi^*

Il-klassifikazzjoni tiegħek

Scritto da: Jeff Hammer

Wiring not easy

NOTE: If ballast disconnect plugs are cut, white wire with red stripe is Neutral. Cap off plain white wire." I listened to that instruction, capping off the plain white wire (in the set of three). However, the light would not work with that wire out of the equation. I ended up having to wire both the white wire and red-stripe white wire to the ballast's white wire. Then it finally worked! I read in one of the other reviews that someone else had to do this. So beware of this note in the instructions.

Scritto da: Ranger Rick

Seems to work OK. The installation information is OK ...

Seems to work OK. The installation information is OK but the programming instructions are awful. I found these details instructions online. Time Delay Program Instructions 1. Push and hold button until LED flashes rapidly (approximately 6 seconds). Release button. 2. Press button twice to enter Time Delay adjustment mode. The LED will flash back the current Time Delay setting according to below table (i.e. 5 flashes for 10 minute Time Delay). 3. Wait approximately 3 seconds 4. Press button the number of times for the desired setting (i.e., press twice for 2.5 minutes Time Delay). 5. LED will flash back this new setting, (repeated up to 10 times). Press button down again until LED flashes rapidly (approximately 6 seconds). Release button. 6. Press button twice to verify Time Delay has been reprogrammed. LED will flash back twice indicating acceptance of new setting Time Delay Settings Table Push Button the number of increments desired 1 ~ 30 Sec 2 ~ 2.5 Min 3 ~ 5.0 Min 4 ~ 7.5 Min 5 ~ 10.0 Min 6 ~ 12.5 Min 7 ~ 15.0 Min 8 ~ 17.5 Min 9 ~ 20.0 Min

Scritto da: Stan

great motion sensor

Easy to install and program, would buy again. Had it for 5 months and no problems. Installed in our pantry for the light and couldn't be more please,no more pull chain to deal with.

Scritto da: Christy Holter

Works great, very sensitive.

Works great even for a low ceiling but is extremely sensitive.

Scritto da: Anchorman-CET

It has worked for 2+ years

I bought this in October 2018. It has worked flawlessly for all this time. Like so many others my only complaint is the instructions. I shiver with dread anytime I think about changing the shut-off timer. Regardless, it's been very reliable thus far.

Scritto da: William Carson

bettb

This works great. I had to modify the installation because I used it on flush mounted fluorescent lights that could not be accessed from the end where it was intended to be mounted. Mounted it on the inside corner and cut a square out of the lens so the cover can be lowered to replace the bulbs. Works great. The next on I get will be able to install it as intended because they will be surface mounted lights.

Scritto da: Joe Donnelly

Works as advertised

Had my electrician install it. He likes it, I like it. It works great. Going to buy a second one

Scritto da: Amazon Customer

Four Stars

Is working well for fixtures in a shop!