Dremel 9901 Tungstenu Carbide Carving Bit, 1/8” (3.2mm) dijametru, Carving & Inċiżjoni Aċċessorju Rotatorju, Cutter Burr (biċċa 1), Fidda

Brand:Dremel

3.7/5

€

DESKRIZZJONI TAL-PRODOTT Rain Bird PRF07530S Irrigazzjoni tat-taqtir Filtru li Jirregola l-Pressjoni 30 PSI, Thread tal-pajp maskili 3/4. Ipproteġi l-komponenti ta 'l-irrigazzjoni downstream tiegħek b'din l-unità kompatta ta' grad professjonali li tgħaqqad il-filtrazzjoni u r-regolazzjoni tal-pressjoni f'biċċa waħda. Billi tnaqqas in-numru ta 'komponenti f'żona ta' kontroll; aktar komponenti jistgħu joqogħdu f'kaxxa waħda tal-valv. B'inqas konnessjonijiet, l-installazzjoni hija aktar faċli u aktar mgħaġġla. Inqas partijiet u inqas konnessjonijiet bil-kamin huma wkoll inqas ċans ta 'tnixxija fl-installazzjoni u matul il-ħajja tas-sistema. L-unità tal-filtru tirregola l-pressjoni għal 30 psi u għatu b'unthreads tal-O-ring tas-siġillar biex jipprovdu aċċess faċli għall-element tal-filtru ta '200 malja għat-tindif. Korp u għatu robusti huma mibnija minn polypropylene mimli ħġieġ għal toughness li jipprovdu klassifikazzjoni ta 'pressjoni ta' 150 psi. Jaħdem mal-valvi kollha u jiġi bi skrin ta 'l-istainless steel ta' 200 malja (75 mikron) installat minn qabel. Speċifikazzjonijiet: daħliet tal-ħajt tal-pajp maskili 3/4 x 3/4 (MPT); firxa operattiva 0.20 sa 5.0 gallun kull minuta; pressjoni tad-dħul 20 sa 150 psi. Disponibbli wkoll (mibjugħa separatament) f'40 psi 1 mudell PRF10040S. Skrin tal-filtru ta 'sostituzzjoni (mibjugħ separatament) huwa mudell #: RBY-200SSMX. Rain Bird "L-Użu Intelliġenti tal-Ilma". MILL-MANIFATTUR Rain Bird Corporation hija kumpanija privata mwaqqfa fl-1933 waqt l-isplużjoni agrikola f'Kalifornja. Aħna rikonoxxuti bħala l-manifattur u l-fornitur #1 ta 'prodotti u servizzi ta' irrigazzjoni fid-dinja. B'uffiċċji tal-bejgħ madwar id-dinja; noffru aktar minn 4,000 prodott ta 'irrigazzjoni li jiffrankaw l-ilma f'aktar minn 130 pajjiż. Sa mill-bidu nett, Rain Bird ipproduċiet u offriet l-aktar firxa wiesgħa ta 'prodotti ta' irrigazzjoni ta 'kwalità għolja għall-irziezet, korsijiet tal-golf, areni sportivi, żviluppi kummerċjali u djar. Matul l-aħħar 80 sena Rain Bird irċieva aktar minn 450 privattiva madwar id-dinja. Inkluż l-ewwel waħda għall-irrigazzjoni fl-1935 fuq il-bexxiexa oriġinali tagħna ta 'impatt-drive (Privattiva ta' l-Istati Uniti #1,997,901) li revoluzzjona l-produzzjoni ta 'ikel agrikolu u wasslet għal era ġdida fl-irrigazzjoni madwar id-dinja. Fl-1990 dan il-bexxiexa tal-impatt oriġinali ġie indikat bħala monument storiku mis-Soċjetà Amerikana tal-Inġiniera Agrikola. Il-prodotti tagħna jkopru l-aspetti kollha tal-irrigazzjoni... tajmers/kontrolluri, bexxiexa rotanti pop-up, bexxiexa pop-up tar-ras tal-isprej, żennuni tal-bexxiex, valvi tal-irrigazzjoni, irrigazzjoni bil-qtar, drenaġġ u ħafna aktar. Dawn il-prodotti ġew magħżula u installati madwar id-dinja fl-akbar u l-aktar proġetti prestiġjużi għall-irrigazzjoni residenzjali, kummerċjali, agrikoli u korsa tal-golf. Rain Bird hija impenjata li The Intelligent Use of Water™ testendi lil hinn mill-prodotti għall-edukazzjoni, it-taħriġ u s-servizzi għall-industrija u l-komunità. Il-wirt tagħna huwa li niddisinjaw u nimanifatturaw biss prodotti tal-ogħla valur u kwalità. Aħna grati li rċevejna bosta premjijiet ta’ rikonoxximent minn ħafna mill-imsieħba apprezzati tagħna. Rain Bird “L-Użu Intelliġenti tal-Ilma

Ammont

Żid mal-CART Ixtri issa

EAN: 0080596034733

Kategoriji Għodda u Titjib tad-Dar, Għodda tal-Enerġija u tal-Idejn, Għodda tal-Enerġija, Għodda li Jdur,

Għall-użu ma 'għodod li jdur li jistgħu jakkomodaw daqs 1/8 shank. X'inhu Inkluż: 1/8 Tungsten Carbide Carving Bit (x1). Il-forma taċ-ċilindru tal-bit tat-tinqix tippermetti tneħħija fil-fond tal-materjal, qatgħat żoni ċatti, truf tondi u tagħmel qatgħat ta 'waqfien u qatgħat V. Ideali għal proġetti bħal inċiżjoni tal-metall jew tal-ħġieġ, tinqix tal-ġebel, jew it-tneħħija tal-flash mill-ikkastjar. Il-bits tat-tinqix tal-karbur tat-tungstenu li jservu ħafna ta 'Dremel jistgħu jintużaw għal applikazzjonijiet aktar aggressivi biex jiffurmaw, twitti, jew itħan materjali iebsin bħal metalli, azzar imwebbes, ċeramika tan-nar, ħadid fondut, plastiks u injam iebes. Importati. metalliku.

Batteries Included?	‎No
Batteries Required?	‎No
Brand	Dremel
Color	‎Silver
Customer Reviews	4.7 4.7 out of 5 stars 743 ratings 4.7 out of 5 stars
Included Components	‎Unit^Instruction Guide
Is Discontinued By Manufacturer	‎No
Item model number	‎9901
Item Package Quantity	‎1
Item Weight	10 Grams
Item Weight	‎0.353 ounces
Manufacturer	‎Dremel
Material	Tungsten Carbide
Material	‎Tungsten Carbide
Measurement System	‎Metric
National Stock Number	‎3455-01-308-4389
Part Number	‎9901
Power Source	‎Corded-electric
Product Dimensions	‎1.6 x 0.8 x 0.2 inches
Size	Pack of 1
Size	‎Pack of 1
Warranty Description	‎No

5 Star

4 Star

3 Star

2 Star

1 Star

Ikteb ir-reviżjoni tiegħek

L-email tiegħek mhux se tiġi ppubblikata. L-oqsma obbligatorji kollha huma mmarkati bi^*

Il-klassifikazzjoni tiegħek

Scritto da: AJ

Did exactly what I needed it to.

I used it to widen a hole on tempered steel. Works great.

Scritto da: chris.w.

Cleared right through a steel bolt and aluminum casing.

Allowed me to "drill" out a sheared-off M6 bolt and enlarger the hole for a threaded repair insert. Cleared through the steel bolt and aluminum casing with minimal effort. Will buy it again when this one dulls out.

Scritto da: Pat

Great tool

Cuts very well doesn't break if used properly. I trimmed 1/8 inch steel with it no problems.

Scritto da: Lady Chozens~

Worked!

Perfect for my use!

Scritto da: Robert Retford

Quality tool

Quality tool at a good price

Scritto da: Benny

Good sharp cutter for mild steel but very brittle

I bought this cutter to make a square hole in a metal stud - the type of metal studs used to hold up drywall in high-rise apartments/offices. The cutter worked great, it moved through the metal stud no problem. I did however have 2 problems that I'm writing this review so that others can benefit from my experience: 1.) The cutter is relatively short. I was trying to cut metal that was behind some drywall. So the cutter had to be long enough to get through the drywall and through the metal. Because of an obstruction on the wall surface, I had to hold the tool about 1.25" away from the metal. This made it so that only the very tip of the cutter would contact the metal. While it worked I can comment that the tool is very short, so consider you application before buying. 2.) The cutter is very brittle. I actually cracked the shaft of this tool and could not complete my job. Because of my particular use, the cutter was bouncing around a bit in the slot I was cutting. This caused the bit to break. After it broke, i used the remaining portion to try to cut again. It broke a second time. Final recommendations: This cutter is good for controlled cuts in mild metals where you can brace/secure the work and the tool. This tool is not very good for free-hand cutting as I was doing. Make sure that you control the tool well to prevent bouncing and cracking of the bit. I think I will re-try with a thicker-shanked bit. Perhaps 3/8" if I can find one.

Scritto da: Lonewolf

Tungsten carbide endmill

Not much to say, they are endmills in Tungsten carbide. Dremel pricing is too high for tooling like this. Came loose bouncing around in a big box, one of the two I ordered was stuck in bottom flap, ready to fall out. Luckily I received both, was close call.

Scritto da: Barry Wagner

Finished the task

I needed to shape an opening I drilled in the end of a hand railing. I was slightly off center and just needed to round over a bit to center the peg. This bit was perfect for the job and did it well and quick. It easily worked its way through oak. Job done.

Scritto da: WellTrainedMonkey

Cuts hardened metal effortlessly.

I was working on turning an old bastard file into a knife and needed some way to add minor details on the handle. This got the job done and it still holds its edge. One slight disappointment is that I found a tiny chip on one of the cutting edge, but thankfully it does not appear to affect the overall performance. Just not sure at what point that happened. Amazing performance considering the cost. Great bit to have with your dremel. I'm very happy with this bit.

Scritto da: Mike

Quality product

Needed to enlarge coil seat hole in the lower control arms of my resto. This did the trick like butter in less than a minute per hole with my Dremel. I had my doubts before purchasing, but proved unwarranted. Very pleased. Good durable product. As advertised.

Scritto da: Salvador elizalde santos

Empaque resellado, posible engaño

Regrese el artículo, porque se notaba que había sido abierto, y resellado, la etiqueta de dremel la blanca que ponen estaba despegada hacia un lado, y el plastico del empaque se veía irregular de un lado, como que fue resellado por eso la regrese, no me gusta el engaño si desde el inicio explicaran que esta nuevo pero resellado podría haber accedido pero esto me parecía un engaño y eso molesta.

Scritto da: AdrianS

Warning: Made in China

I bought a couple of these, together with some 9904 bits. While the 9904's are made in the US, the 9901 have the dreaded "Made in China" printed on them. After my experience with Chinese "titanium coated" drill bits, I expect that they are no better than the regular multipurpose bits, but at least twice as expensive (which seems to be confirmed by reviews on amazon.com). If you want Chinese cutting bits, you can get them much cheaper elsewhere, instead of paying a premium just for the Dremel logo.

Scritto da: Jody Wright

Performance on metal

I used this cutter with my Dremel to remove excess metal on new door strikes mounted on metal door frames installed with new handles. Now the doors close and lock with perfection.